The Ultimate Tomato Cage in 5 Simple Steps

baymule

Sustainability Master
Joined
Nov 13, 2010
Messages
10,698
Reaction score
18,586
Points
413
Location
East Texas
I put up cow panels for a tomato trellis. I composted the area, then laid cardboard down. I made a double planting row by spacing 3 cow panels 18" apart. The cow panels are held up by T-posts. I cut holes in the cardboard with a machete and planted my tomato plants. I am going to leave them in place, in the fall, place paper feed sacks in the rows and compost heavily. At our previous home, I planted tomatoes in the same bed for 9 years, because it got the most sun and the plants liked it there. So there should be no problem in leaving my tomatoes in a permanent place.

IMG_0653.JPG


IMG_0630.JPG
 

MoonShadows

Almost Self-Reliant
Joined
Feb 24, 2016
Messages
925
Reaction score
794
Points
167
Location
not here
Great pics, bay! After posting this thread, I wound up using welded wire posts that I nailed in to the sides of my raised gardens for tomato supports. I'll most likely attach 1 x 2's and tie the tomatoes off or use the Florida method. I just decided the trip to TSC wasn't going to get done, and I'll save a few bucks right now.
 

Denim Deb

More Precious than Rubies
Joined
Oct 21, 2010
Messages
14,993
Reaction score
616
Points
417
I tried using the Florida weave one year. But I had tomatoes growing at different rates. Plus, they grew so fast that year I couldn't keep up w/it.
 

MoonShadows

Almost Self-Reliant
Joined
Feb 24, 2016
Messages
925
Reaction score
794
Points
167
Location
not here
Yes, Florida weave...I knew Florida method was not the right term, but I just couldn't remember the right term. Thanks for that.
 

Beekissed

Mountain Sage
Joined
Jul 11, 2008
Messages
12,774
Reaction score
3,934
Points
437
Location
Mountains of WV
I did that one year and it was a disaster! My tomatoes get huge ~6-7 ft tall~and the fruit is heavy so the strings kept breaking all over. I spent all season trying to keep the strings from cutting into the vines that were bowed over them and trying to keep the strings tied back into place.

Don't know what kind of maters they grow in Florida, but they couldn't be indeterminate beefsteaks. :hu
 

MoonShadows

Almost Self-Reliant
Joined
Feb 24, 2016
Messages
925
Reaction score
794
Points
167
Location
not here
Well....after all that talk about tomato cages and cow panels, I didn't buy the cow panels. I wound up attaching green metal fence posts to the side of my raised tomato garden and started stringing nylon rope to tie the tomatoes tp...already have a few small green ones...not bad for this early in the season around these parts. You can see a couple of little volunteers that I moved to the corners.

100_1132.JPG


Here's a pic of the lettuce. SOOOOOO much lettuce. Hope we can get most of it eaten before the real hot weather gets here. It's been unseasonably cool the past week or so.

100_1133.JPG


I just put in some beet and turnip seeds in another raised gardens. They are just starting to come up.

Here are my beans, carrots and spinach, although the spinach germination was a disappointment.

100_1141.JPG


100_1142.JPG


And, we finally moved the massive dirt pile in the backyard and replaced it with some marigolds, portulaca and a couple of red knockouts. Need to plant some more grass.

100_1137.JPG
 

Mini Horses

Sustainability Master
Joined
Sep 2, 2015
Messages
7,070
Reaction score
14,452
Points
352
Location
coastal VA
Baymule I like you setup and you could run a board or piece of PVC across there if you needed more between the plants.
Moonshadows your raised beds look great! chickens love lettuce! Even tho they have plenty of grass in the pasture.

Another easy to make/use/store idea is to use PVC pipe. If you angle cut bottom you have a spike to drive in. Prior to that you drill holes thru a large diameter pipe, up & down the length, to slide smaller pipe thru and you can make a support system of many sizes & configurations. Just disassemble when growing season over & store for next time. No rot, moveable and you can fill the large diameter with water to drip into ground for slow watering. Of course, only to height of first hold, LOL. But, the pipe in ground (or a gallon jug with small holes in bottom) both make a slow water system if you have a group of plants needing this.
 

Dianna Starr

Power Conserver
Joined
May 16, 2017
Messages
15
Reaction score
10
Points
25
I read this on the Growing a Greener World website. I have experimented with many ways to tie up tomatoes over the years, but none ever seem to be totally sufficient. I am going to use this method this year. As the author says, they are sturdy, tall enough, wide enough, rust resistant, attractive, easily storable and long lasting.

The Ultimate Tomato Cage in 5 Simple Steps

By Joe Lamp'l on June 8, 2015

Of all the plants I grow in my edible garden, I have to say, my favorite are tomatoes! But, I don’t love the constant challenge of trying to keep them supported as they get really tall and wild. Yes, I’ve tried just about everything, but nothing worked well enough and at the same time, looked good enough in the garden for my taste…until now.


My “ultimate tomato cages” at work in the GGWTV garden. There are 24 and counting!

My ah-ha moment came as I was looking for more uses for those incredibly versatile livestock panels. I use them all around the garden, for supporting vining crops like cucumbers and peas, keeping my goats from eating some of my plants and one of my favorite uses, setting them on top of the beds at planting time for a handy grid template.


One of my favorite uses of these versatile panels is for my planting templates.

So why not use them for supporting tomatoes too? They meet all 7 of my criteria for what it takes to be considered the ultimate tomato cage: sturdy, tall enough, wide enough, rust resistant, attractive, storable, and long lasting.

You get livestock panels at the farm and tractor supply stores. Each one is 16 feet long and just over 4 feet wide. They’re made of galvanized metal and super sturdy.

Although I’m sure I didn’t invent this method for supporting tomatoes, I’ve never seen it in use, so my design is just what evolved through trial and error and settling on the ideal size for me. Yet these panels are large enough to adapt to almost any size you prefer.

In my case, I get one complete cage at the height and width I like, with some pieces left over that I can use elsewhere in the garden. That way, the entire panel gets used with no waste. While you might consider the cost of a livestock panel at $20 a bit expensive for a single tomato cage, considering that these will last for years and with all the usable excess pieces, I think it’s a very good deal.

You just need two things to make these cages. One livestock panel for each cage (select the panel style that has a grid pattern approximately 6 inches square). You also need a pair of bolt cutters. My pair cost about $22 at Home Depot and well worth it. I tried a smaller pair but found they made my the palms of my hands sore after a short while of cutting. For the small difference in price and a one-time purchase, the larger size is well worth it.

Here are the steps on how I make the Ultimate Tomato Cage:

1. Place one full livestock panel on a flat surface. A driveway works well. Using a complete panel, count across the width so you have six complete squares and cut away the rest, all the way down the length of the panel.


Large bolt cutters and a flat surface make for quick work

2. With the width of the long panel now reduced to 6 squares, I count down from one end 9 squares, and cut all the way across, just above the horizontal piece at the bottom of this 9th square.


With the width of the original panel reduced to the desired size, now it’s time to cut for the desired height.

I prefer the bottom of this panel to have long vertical pieces that can be driven extra deep into the soil to serve as the anchoring stakes. If you choose this extra deep option, then cut away the horizontal pieces one level up at the 8th square also (the equivalent of two squares deep) as shown below.


Cut away the horizontal pieces, between the vertical pieces. This leaves long spikes to anchor each panel in the soil.

3. I then repeat step 2, starting from the other end of the original panel and count down 9 squares. Once you cut across this piece, you now have 3 remaining pieces. The middle piece is now a nice sized panel with many versatile uses in and around the garden.

The two remaining pieces are what will make up your cage support.

4. Place one of the sections under a piece of straight lumber at least as long as the panel so that 3 squares are showing against the straight edge of the lumber. I like to have the panel facing up so the long vertical rib is resting against the edge of the wood edge. This serves as a good guide and support as you bend up the panel from the outside edge towards you until you get a 90-degree angle.


The edge of a board serves as a good anchor for leverage and a straight guide for bending the panel towards you.

Then simply repeat this process for the other panel.

5. Stand the panels so the lose spike ends are facing up. Take a second to straighten each one so when they are set in place in the soil, they all go in evenly.


Taking a few seconds to straighten the ends will make inserting them into the soil much easier.

Now it’s simply a matter of inserting them in the garden bed around each plant so that when both panels are installed, they form a square cage with the plant centered in the middle.


With straight spikes as the anchors, both panels should match up nearly perfectly.

A final but optional step to make it tidy is to secure each piece together with small cable ties. I use 4-inch ties, one at the top, one in the middle and one towards the bottom of each seam. This holds the panels firmly together and gives added stability and a seamless, solid look.


The tomato plants adapt beautifully while growing into their new homes.

That’s all there is to it. These cages are super sturdy, tall enough and just wide enough so as not to crowd the plant but still leave ample room for other cages in the bed. However, if you prefer even a taller or wider cage, a single panel in its original size allows for both.

At the end of the season, cut away the cable ties, separate the panels and stack them in a neat pile until the next time, and for many years after that.

So what do you think? Do you like? How would you improve upon this? I would love to put all the brainpower out there to work. I’m anxious to hear your thoughts!
 

Dianna Starr

Power Conserver
Joined
May 16, 2017
Messages
15
Reaction score
10
Points
25
all of these are very good ideas, using this type of cattle fencing , but my tomatoes i planted on the side of our barn, 1st because it had the best light in that lactation , ( here in AZ that means not to much sun ) & in that location they grew like 8 to 9 feet tall HA dont know why..? i took pic's of my 65" tall hubby to show our tomatoes grew way over his head HA , but my present problem is my 75 free range chickens would if they could eat every plant they could get a hold of :( so i think i need a chicken proof tomato cage & one they cant get their heads into HA
 

Latest posts

Top